MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE DPVH890GJMV
Vermillion Red gas steam DPVH890GJMV: distinguish its lint reminder from SteamRefresh completion.
Exact model and panel
The Vermillion Red DPVH890GJMV is a GE Profile gas dryer whose exact product listing includes SteamRefresh and Steam Dewrinkle. It has a 7.5 cubic foot stainless steel drum, DuoDry moisture sensing and an electronic control panel in a 27 inch wide, 31 1/8 inch deep and 39 3/4 inch high cabinet. These details establish what the full GJMV suffix identifies: a gas, red, steam-capable DPVH890 rather than another model in the Profile manual family. GE links that SKU directly to the owner's PDF. Its cover identifies DPVH890, and the rendered control page shows the steam selections on the model's cycle interface. The product page also confirms the Clean Lint Filter Reminder Light and a delay-start capability of up to twenty-four hours. The owner should compare the model plate with this full suffix before following an option described elsewhere in the shared manual, since neighboring family members have controls and optional modules that are not interchangeable.
What the indicator means
The filter message on the DPVH890 display reads CLEAN LINT FILTER. Page seven gives a precise duration: it stays on for fifteen minutes following completion of a cycle. GE calls it only a reminder. Its appearance at that moment is therefore not a sensor test of airflow, lint mass or duct temperature, and it is not a numeric fault code. Clean the lint screen before the next load even when the message has timed out. If a load is under-dried, use the actual fabric mix, selected cycle and exhaust conditions to narrow the problem; do not claim that the reminder identified the cause. The panel can also give Damp Dry Signal at a partly dried stage and a variable end-of-cycle signal. These notifications represent different events. Writing down whether the machine was still running, had just stopped, or was within the fifteen-minute reminder window prevents a routine post-cycle display from being recorded as an active malfunction.
Cycles and practical use
Steam use gives this red DPVH890 a separate set of operating questions. Its exact GE specifications list both SteamRefresh and Steam Dewrinkle, and the guide's page nine says SteamRefresh automatically selects Extend Tumble. When that steam program completes, the display says Garments Ready and the dryer keeps tumbling until the door is opened. Thus a continuing drum after Garments Ready should first be checked against the programmed Extend Tumble behavior, not grouped with CLEAN LINT FILTER. The product also lists specialty choices such as Fleece, Pet Bedding and Performance Fabrics, while its twenty-four-hour Delay Start schedules a later cycle. The moisture sensor's estimated time may change as a heavy item dries. Steam program, specialty program, delayed start, damp signal and lint reminder each have distinct meanings and timing on the exact panel. Page thirteen of this PDF reserves Demand Response for model DPVH891; no Demand Response ability is asserted for DPVH890GJMV.
Care and a focused check
For ordinary care, page twelve says to pull the lint filter upward, clear its fibers before every use and replace it. If dryer sheets create a waxy coating, GE specifies washing the screen with warm soapy water and drying it thoroughly. Interior and exhaust duct cleaning by qualified personnel is recommended annually. Steam cycles can create different expectations about remaining moisture and garment movement, so a report should identify whether SteamRefresh, Steam Dewrinkle, a sensor cycle or timed drying was selected. The observed message should be transcribed exactly: Garments Ready after SteamRefresh is a completion notice, while CLEAN LINT FILTER is a scheduled housekeeping reminder. If heat or drying is genuinely poor, compare load size, vent discharge and program choice after filter care, then use qualified service and the gas installation guidance as appropriate. A clear report with GJMV suffix, red finish, cycle, display text and sequence gives a technician more value than the general statement that the machine showed an error.
Verified model details
Exact product and PDF panel support SteamRefresh and Steam Dewrinkle.
Source for this detailCLEAN LINT FILTER lasts fifteen minutes after the cycle; it is only a reminder.
Source for this detail · Source page: 7
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ 7.5 Cu. Ft. Colossal Capacity Gas Dryer - DPVH890GJMV - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.