MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE JEB1095WB
GE JEB1095WB is a white 27-inch built-in 800-watt microwave/convection oven with combination roasting and two distinct display states: sensor Error and normal hot-cavity HOT.
Three cooking methods in the white built-in JEB1095
JEB1095WB is a white, one-cubic-foot built-in oven for a 27-inch cabinet, rated at 800 watts of microwave output. Its exact GE page specifies a stainless-steel interior and convection cooking, unlike a microwave-only JEB1055. The linked use-and-care cover calls the JEB1095 base model a built-in microwave/convection oven; the WB suffix and exterior color are confirmed by the exact product listing. With ten microwave power levels and five-stage programming, it can heat by a timed microwave method, circulate hot air for browning, or use a combination method. Combination Cook and Combination Roast are both real controls on this SKU. The owner guide explains that combination cooking alternates microwave energy and convection heat to speed cooking while browning. Thus a cooking time, rack instruction or dish material from pure microwave operation cannot automatically be transferred to convection or the mixed method.
Shelf, cookware and probe depend on the mode
The physical accessories tell an owner which method is in use. Page seven says the metal shelf must rest on the cavity floor for convection and combination cooking, then be removed for microwave-only cooking. This is a deliberate mode rule, not a contradiction about whether metal exists in the appliance. The page-eleven cookware chart permits metal pans for convection but marks them unsuitable for microwave and combination settings. Heat-resistant glass or plain ceramic is allowed across the three methods, whereas ordinary plastics cannot be put into convection heat. Combination Roast uses the temperature probe inserted in food and firmly connected to the wall receptacle; a loose probe can prevent starting. Sensor Popcorn, Reheat, Cook and Beverage instead use steam from food, not the roast probe. The exact product includes a wire rack and Temp Cook/Hold, but the appropriate shelf, vessel and probe choice follows the mode selected on the touch panel.
How Error differs from a hot cavity
The display word Error in the JEB1095 problem solver refers specifically to the four steam-based sensor programs. The table on physical page thirty-two says the door opened before steam could be detected, or steam did not appear within the maximum sensing time. Sensor Cook shows AUTO while it waits for vapor. An early door opening lets vapor escape, so record whether it happened and what food and covering were used before concluding that a component failed. HOT is a different displayed word on the same page. GE calls it normal after opening a cavity hotter than 200 degrees Fahrenheit and notes that sensor pads will not operate at that temperature. Such heat can follow convection or combination cooking. Allow the oven to cool before choosing a sensor program. HOT should not be converted into an electrical error, and Error should not be explained solely by residual convection heat without the observed sequence.
Reading the panel before requesting service
A third message, PRObE, can appear when a probe-required roast or Temp Cook/Hold setting lacks a securely seated temperature probe; that is separate from steam detection. After a power interruption the clock panel may show RESET, requiring CLEAR/OFF and a new clock setting. End reminders and a kitchen timer can sound without indicating a fault; the timer itself uses no microwave energy. When the lighted panel does not start a selected cycle, the manual also asks for door closure, the Start key, and whether an earlier selection was left active. These checks are useful because a hot cavity temporarily rejects sensor keys by design. Record the exact visible word, selected microwave, convection or combination method, whether the metal shelf and probe were fitted, and whether the door had been opened. Those concrete details let service distinguish a program condition from a hardware problem without treating every panel word as the same code.
Verified model details
This JEB1095 combines microwave, convection and probe-guided combination modes.
Source for this detailError belongs to a steam-sensor phase, while HOT flags a cavity above 200°F.
Source for this detail · Source page: 32The metal shelf and cookware rules change with the selected heat method.
Source for this detail · Source page: 11
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ Built-In Microwave/Convection Oven - JEB1095WB - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.