MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE PDT855SIJII
GE PDT855SIJII needs a custom panel and handle and uses an 800 Series, three-level wash system. Its exact Floor Protect with Alert feature supports the manual’s LEAK DETECTED display warning.
Recognize the integrated PDT855 and its panel row
PDT855SIJII is a GE Profile dishwasher intended for a custom exterior panel and handle. The II suffix should therefore be read before following cleaning advice meant for an exposed stainless door. GE’s exact product page specifies a top-control LCD display, a door cycle-status bar, white LEDs and separate Clean, Sanitized and Low Rinse Aid indications. Its linked owner guide names a PDT845/PDT855 control drawing on page six, which is the correct row among several family panels. The product specification also includes Sabbath/Door Wake-up mode and built-in WiFi. Those controls are more specific than the generic family cover. The same exact page lists Floor Protect with Alert, resolving the guide’s “on some models” wording for a displayed leak warning. A custom panel may conceal the controls when the door is shut, but the model identity and LCD text still govern any troubleshooting decision.
Use three racks and the 800 Series water path
The washing hardware explains several decisions before a fault is suspected. GE calls this an 800 Series, three-level wash system with variable-speed dual pumps and motors, more than 140 spray jets, Deep Clean silverware jets and automatic HotStart. The exact product also lists a full third rack, a three-piece silverware basket with cell covers and independently selectable upper and lower wash zones. Unlike a two-rack machine, a thin utensil placed on top can free room below, while the covered basket keeps small flatware separated where the dedicated jets can reach it. The manual gives upper-rack drawings specifically naming PDT855 among a small group, including a twelve-place-setting arrangement. It says the upper rack can move two inches, yet warns that a loaded rack can be heavier than expected. Before judging a weak wash, look for utensils crossing spray paths or a large tray in front of the dispenser: the lower-rack instructions say this can block jets from rinsing out detergent. AutoSense varies washing in response to sensed soil; it is not a fixed-time test of the pumps.
Distinguish the leak display from timing and status
An actual LEAK DETECTED message has a defined outcome in this manual. Page six says leak protection drains the dishwasher and stops its cycle, and page twenty-two repeats the instruction to call for service. Because the exact PDT855SIJII page specifies Floor Protect with Alert and the manual’s drawing explicitly labels PDT855, the warning is applicable to this model even though the family guide says only some models have it. It is a written display indication, not a numerical code or the same as the Clean light. Status needs context: Sanitized illuminates only if the required sanitation conditions were reached, and an interrupted or insufficiently heated cycle may leave it off. The start sequence in this edition allows four seconds to close the door after pressing Start; a missed window can look like a failed start. Holding Start for three seconds is the documented cancellation action and itself causes draining. Record the screen words and the action just taken before attributing every stopped wash to a leak.
Maintain the integrated front and record useful service facts
The integrated finish creates a practical maintenance distinction. Page twenty of the manual identifies an II ending as an integrated door, rather than the separate SS stainless-front treatment; follow the appropriate panel maker’s care guidance for the fitted custom surface. The dishwasher’s own control strip can be wiped with a lightly damp cloth and dried. Behind the door, GE advises periodic filter inspection, especially if dishes feel gritty or cleaning declines. It also says an installed air gap should be examined when water drains poorly. These routine observations do not override a displayed leak warning and cannot by themselves identify a sensor fault. When requesting service, give the full PDT855SIJII identifier, the custom-panel installation, the selected wash zone and cycle, the difference between actual standing water and normal drainage after cancellation, and the exact LCD message. This information uses the model’s unusual integrated design and 800 Series flow arrangement, so the investigation is tied to the appliance rather than a generic dishwasher symptom list.
Verified model details
The official guide draws PDT855 controls with PDT845, separate from simpler series.
Source for this detailCustom panel and handle requirements matter when identifying the exact II suffix.
Source for this detail · Source page: 6The 800 Series wash circuit uses variable-speed dual pumps and 140-plus jets.
Source for this detail · Source page: 22
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ Stainless Steel Interior Dishwasher with Hidden Controls - PDT855SIJII - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.