MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE PF80S10FPY
GE Profile GeoSpring PF80S10FPY is an 80-gallon, 120-V smart hybrid heat-pump water heater with FlexCapacity. GE lists its cabinet at 76.375 × 27 × 27 in. (H × W × D), useful measurements to check before installation. Its control offers Heat Pump, Hybrid, High Demand, Standard Electric and Vacation modes, which balance energy use and hot-water recovery; on this FlexCapacity model, Normal, High and X-High settings change usable hot-water output through an integrated mixing valve.
Exact model and cabinet
PF80S10FPY is GE's 80-gallon GeoSpring heat-pump model marketed for 120 V with FlexCapacity. PF80S10FPY has a published first-hour rating of 94 gallons. GE gives the cabinet a 76.375-inch overall height and a 27-inch width, so this larger storage choice requires both ceiling clearance and a route wide enough to bring the unit into place. Its 120-V designation identifies the version sold, while the detailed sheet also allows a specified conversion from 120/110 V, 15 A to 240/208 V, 25 A. That option does not make the physical installation automatic. Check the pipe connections, service access and exact electrical instructions before treating an existing heater location as reusable.
FlexCapacity configuration
This PF80S10FPY is a FlexCapacity version. GE's manual describes Normal, High and X-High usable-hot-water settings operated through an integrated mixing valve. This is separate from choosing Heat Pump, Hybrid or another heating mode: one selection concerns delivered hot-water capacity, the other concerns how the tank is heated. Treat the outlet temperature and scald warnings seriously, especially when increasing a setting. The matching FlexCapacity fault list includes mixing-valve and outlet-sensor conditions that should not be transferred to a non-Flex model.
Heating modes
For a household deciding how to run PF80S10FPY, the manual's mode descriptions are more useful than an efficiency slogan. The available choices include Heat Pump, Hybrid, High Demand, Standard Electric and Vacation. Hybrid is the normal mixed strategy; High Demand brings in the heating elements more readily for recovery, whereas Heat Pump emphasizes compressor operation. Vacation is intended for periods away rather than ordinary heavy use. Check both the selected mode and the water-temperature setting when evaluating output; changing a mode does not repair a fault code.
Temperature decisions
The PF80S10FPY control lets an owner review and change the set water temperature, but GE warns that hot water above 125°F can cause severe burns. Where a tempering or mixing arrangement is present, the delivered temperature can differ from the tank setpoint. The owner's manual discusses choosing a suitable setting for the household and warns against using the display alone as proof that water at a faucet is safe. A qualified installer should handle plumbing or wiring changes; the product title's voltage is not an installation procedure.
Filters and tank care
In Heat Pump, Hybrid and High Demand operation, PF80S10FPY moves air through three filters. GE says the Filter indicator illuminates when they need attention; the manual describes removing, cleaning, drying, reinstalling and resetting the filters. A clogged filter can reduce effective heat-pump operation, so the indicator is a maintenance cue rather than a compressor diagnosis. The same care section describes the condensate drain; a blockage there has a separate alarm. Use the cited procedure and keep electrical parts dry during routine care.
Interpreting fault codes
The FlexCapacity diagnostic table for PF80S10FPY separates heating faults from mixing-valve faults. F10 and F20 concern the lower electric element; F11 and F21 concern the upper one. F16 or F17 can follow a mixing-valve outlet safety cutoff, and F18 or F63 describes integrated mixing-valve failure. The same code list includes tank and outlet temperature sensors, so a temperature complaint is not one single diagnosis. Read the full code and the linked manual table before arranging service; internal electrical and valve repair is not a routine owner check.
Verified model details
80-gallon, 120-V smart hybrid heat-pump water heater with FlexCapacity.
Source for this detailCabinet dimensions: 76.375 × 27 × 27 in. (H × W × D).
Source for this detailHeat Pump, Hybrid, High Demand, Standard Electric and Vacation modes.
Source for this detail · Source page: 8On this FlexCapacity model, Normal, High and X-High settings change usable hot-water output through an integrated mixing valve.
Source for this detail · Source page: 9
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE PF80S10FPY product support and owner manual
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.