Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE PHB920BJTS
PHB920BJTS is a GE Profile 30-inch induction range with a 5.3-cubic-foot convection oven, ceramic-glass surface, storage drawer and an oven F function-error pattern.
Identify induction, oven and drawer
PHB920BJTS is GE Profile's 30-inch free-standing range with an induction surface and a 5.30-cubic-foot convection oven. The exact GE record specifies an 11-inch, 3,700-watt Power Boil zone at the front right and a 6-inch, 100-watt warming zone in the center. That center zone is a distinct low-power warmer, not another induction coil of the same output. The cooktop is gray patterned ceramic glass, and the lower drawer is for storage. The linked official manual cover identifies PHB920, while the full BJTS suffix on the product page establishes this precise configuration. In an appliance with both a cooktop display and an oven display, the location of a flashing message is critical. Copy the full model and serial from the appliance before looking up parts. The surface may still feel hot after a pan is removed because the glass receives residual heat from cookware, even though induction energizes the ferrous pan rather than directly heating the glass.
Troubleshoot the cookware before a zone
A magnetic, flat-bottomed pan of sufficient size is necessary for an induction zone to stay on. The manual suggests a magnet check and centering the pan over the marked circle. It explains that a pan that is nonferrous or too small makes that zone's power-level display flash for thirty seconds and then shut off; removing a suitable pan for over thirty seconds also stops power. The page 23 troubleshooting chart starts with cookware type, dimensions, centering and full contact with glass. These checks should come before treating a blinking level as an electronic oven F code. Glass can be scratched by sliding rough cookware, and a wet lid can stick as it cools. The warming zone uses different cookware rules because it is not an induction coil. Note which zone was selected, whether the pan passes a magnet test and whether the power digits blinked. Those details distinguish a normal pan-detection response from a fault that persists with suitable cookware.
Choose the correct oven and cleaning mode
The electronic oven panel has Bake, Broil, Convection Bake and Convection Roast, plus separate Self Clean and Steam Clean keys. The exact GE listing confirms convection and the steam-clean option, rather than requiring inference from a multi-model drawing. Page 11 says Cook Time ends the oven operation at its programmed limit, while the kitchen timer is only a countdown. Use rack positions and leave space around multiple pans for the fan to move air; the cooking guide treats single-rack Bake differently from convection on several levels. The high-temperature Self Clean cycle locks the door and asks for removal of cookware and ordinary shiny racks, allowing only the specified dark enameled racks to remain. Its time can be chosen from three to five hours. Steam Clean is a different shorter, lower-temperature process and should not be described as the same cycle. A drawer below the cavity stores items and should not be mistaken for an oven compartment or warming drawer.
Separate oven F from cooktop blinking
The page 24 table names flashing F plus a number or letter in the oven display a function error. It instructs Cancel/Off, an hour of cooling and a retry. If it repeats, disconnect all oven power for at least thirty seconds, reconnect and ask for service if F returns. Record the exact suffix and whether Bake, Convection or cleaning was active. The manual does not assign each F suffix to a component, so do not replace a sensor based only on the characters. A cooktop zone showing flashing power instead of F calls for the pan checks on page 23. A self-clean door still locked after the displayed time may need to cool below the lock temperature, and a clock that flashes after an outage needs resetting. These separate conditions prevent a diagnosis of the induction surface from being confused with the oven's control message.
Verified model details
An induction zone's blinking power level usually calls for a pan compatibility and placement check.
Source for this detail · Source page: 1The oven provides separate Self Clean and Steam Clean controls; the lower drawer is storage.
Source for this detail · Source page: 24The troubleshooting F pattern belongs to the oven display, not to a cooktop pan warning.
Source for this detail · Source page: 10
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ 30" Free-Standing Convection Range with Induction - PHB920BJTS - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.