MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
MODEL OVERVIEW
About this model: LG DLEX8600BE
The matte-black LG DLEX8600BE electric LCD dryer documents actual sensor, supply and 80/90/95-percent duct messages in its exact support-linked manual.
What the DLEX8600BE actually is
The DLEX8600BE is the matte black electric member of LG's 8600 rear-control dryer range. LG's exact-model specification gives it a 7.3-cubic-foot capacity, names WT8600CB and WT8600CW as matching washers, and distinguishes this electric unit from the DLGX8601 gas version. That distinction matters when reading the shared owner's manual: its gas connection and burner checks describe a different machine. For this model, use the electric supply and venting instructions. The specification also identifies an EasyLoad door and four-way electric venting, details worth checking against the installation site before treating a slow cycle as a machine fault.
The owner manual cover identifies the DL*X860**E family, and its pictured control panel agrees with the rear digital-dial arrangement shown in the DLEX8600BE specification. A central selector sits beside an LCD and separate temperature, dryness, time, Steam and Settings controls. The LCD reports the selected settings, estimated time and status messages; the indicator area separately shows Flow Sense, control lock, remote start and Wi-Fi. The Previous and OK buttons navigate menus. A message on that screen therefore needs its own context: a lock or network icon is an operating state, while the troubleshooting table names faults that need attention.
Choosing a useful cycle
LG lists 24 cycles and 20 options for this exact electric SKU. The default menu includes AI Dry, which adjusts drying time and temperature after sensing characteristics of the load; Bedding for bulky items; Delicates for easily damaged fabrics; and a high-temperature Antibacterial cycle. Quick Dry is a timed choice for a small load, while Timed Dry lets the user choose 10 to 100 minutes in ten-minute steps. The less prominent cycles are accessed through Cycle List Edit. In that menu, Small Load is intended for up to three items, Large Load Dry is tuned for a half load, and X Large Load Dry for a full load. These names have distinct load assumptions rather than being interchangeable shortcuts.
TurboSteam is fitted to DLEX8600BE. Steam Fresh is a ten-minute cycle for reducing wrinkles and odours in dry fabrics; Steam Sanitary combines steam with high temperature. The manual excludes particular delicate, foam, down and leather items from those cycles, so the garment label still controls the choice. Steam needs a cold-water hose, and the installation chapter explains how to use a Y-connector when a washer shares the tap. Energy Saver starts a Normal cycle with an air-dry period and lengthens drying time; a cool beginning with that setting is expected. Steam and Energy Saver cannot be selected together. Wrinkle Care can tumble intermittently for up to three hours after completion.
Reading the actual diagnostic messages
The rendered troubleshooting table on page 56 uses written LCD messages, rather than the tE and d-number glyphs found in some other LG dryers. “Temp sensor error 1” means the temperature sensor has failed; LG says to switch the dryer off and call service. “Power supply,” “High voltage,” or “Low voltage” points to an incorrectly connected power cord in that operating table, so the terminal-block connection needs checking. Do not infer a gas-supply fault from those labels: the exact DLEX8600BE is electric. The installation-test table on page 32 also includes “Humidity sensor error,” with the same turn-off-and-service direction. It treats supply problems as either wiring or household protection issues, depending on the cause.
The same operating table calls out “Duct blockage (80%), (90%), (95%).” These are severity messages about the exhaust route, not three unrelated electronic failures. The manual warns against continued use with a severely restricted exhaust because of fire and property-damage risk. It directs the user to check airflow at the outside vent, look for too many bends or an overlong run, and clear or repair the duct. The separate Flow Sense indicator can show four bars during drying. A partially blocked duct may still allow operation but will extend drying time and increase energy use. After the restriction is removed, Flow Sense may require several consecutive cycles to reset; LG advises service if it remains active after more than five.
Installation test and routine care
For a new installation, the manual describes a short exhaust test: run it empty with the appliance cool, switch on, immediately hold Wrinkle Care and Settings, and confirm “Install Mode” appears before pressing Start/Pause. That text is a successful test-start state, not a fault. At the end, a lit Flow Sense LED means the exhaust should be checked. LG cautions that the installation result and a normal drying-cycle result can differ, because the latter is more accurate for the home's duct condition. The electric heating check is separate: after starting Timed Dry, the exhaust air should be warm after three minutes. A qualified installer should handle any mains-wiring correction.
The lint filter should be cleared after every cycle and never omitted. LG asks for duct inspection for lint once a month and cleaning at least once a year, with immediate attention if airflow or drying performance falls. These checks distinguish a genuine ventilation message from a load or maintenance problem. On the LCD, Language can change the screen among English, Spanish and French, while button labels stay as printed. The ThinQ app can monitor a cycle, receive a problem notification and use Smart Diagnosis; remote control stops if the door is opened. Those connected functions add information, but the exact manual's page-56 text and the actual panel message remain the starting point for diagnosing this DLEX8600BE.
Verified model details
Exact DLEX8600BE electric 7.3-cu-ft rear-LCD EasyLoad model
Source for this detail · Source page: 1Rendered LCD messages for Temp sensor error 1, supply and duct blockage
Source for this detail · Source page: 56Install Mode is normal; gas-only checks are excluded
Source for this detail · Source page: 32
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
LG DLEX8600BE.AEBEEUS: Support, Manuals, Warranty & More | LG USA Product Support Page
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.