MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MLH27N5AWWC
The MLH27N5AWWC manual identifies five display messages; this guide links them to the exact Canadian washer and its owner checks.
Confirm the Canadian washer and its controls
Midea Canada lists MLH27N5AWWC as a 3.1-cubic-foot front-load washer with a slim 24-inch form intended for tight spaces. The exact product page says it can be stacked with a compatible 4.4-cubic-foot ventless heat-pump dryer; do not treat that dryer description as a washer specification. It advertises sixteen preset wash cycles and eight options, a Water Cube drum and an interior heater that can lift water temperature to 60°C. Its listed maximum spin speed is 1,300 rpm and the body measures 23.4 by 23 by 33.5 inches. The official PDF cover prints MLH27N5AWWC, connecting the instructions below to this precise suffix. Verify the machine's rating label before interpreting a code, because the manual's display meanings should not be borrowed for another compact washer.
Rule out setup problems before blaming electronics
The installation chapter gives a required inlet-water pressure range of 0.05 to 1 MPa. Pressure below the lower end can lengthen filling until the washer reports an error, so a fill message does not by itself prove a failed inlet valve. Four shipping bolts must be removed before operation; leaving them installed can produce excessive vibration and movement. After installation, the manual proposes an empty Rinse & Spin test cycle to check filling, draining and stability. If there is a visible leak, examine the hose connections and stop the test before continuing. The washer needs an appropriately grounded supply. These installation points matter because a hose, power or leveling problem can mimic a machine fault even though the eventual display code is real.
Separate ordinary display behavior from faults
The digital display initially shows the estimated duration of a selected cycle, then process and time remaining; load size, incoming temperature and pressure can change the actual duration. The panel offers Highest, High, Medium, Low and No Spin, while the temperature key cycles through Hot+, Hot, Warm, Eco and Cold. Initial settings are Normal, Warm and Medium spin. Delay can be set from zero to twenty-four hours, and the display then shows the scheduled start rather than a malfunction. To pause, hold Start/Pause for three seconds and wait for the drum to stop. The door may stay locked when water is high or hot; forcing it is unsafe. Note which cycle and controls were active before photographing a suspected error.
Read the five printed codes precisely
On physical PDF page 41, E30 means the door is open or not seated; close it and check for trapped fabric. E10 names a water-injection problem while washing: check adequate pressure, straighten the inlet hose and inspect the inlet-valve filter for blockage. E21 means the machine is not draining; check the drain hose for obstruction. E12 is the manual's water-overflow code and its table says to restart the washer. EXX is a general other-error label rather than a named part: try the documented restart and contact qualified service if the code remains or changes. Keep E10 and E21 separate because inlet and drain checks lead to different hoses. Write down the exact characters before resetting the machine.
Maintain safely and know when to request service
Before maintenance, the owner chapter says to switch off, unplug and close the water taps. It suggests an empty Tub Clean cycle about once a month to address odors; this routine is not a cure for an electronic or overflow code. An emergency door-release cord is described, but the warning forbids using it while the washer runs and tells the user to wait for water to cool. Do not turn that cord into a shortcut when E21 leaves water inside. A persistent E30, E10, E21, E12 or EXX after the listed checks calls for qualified service. When requesting help, report MLH27N5AWWC, the code, the selected cycle, whether the door could open, the water level and any leak or unusual vibration. That record helps distinguish a simple setup issue from a repair.
Verified model details
Exact 3.1-cu.-ft. Canadian stackable model
Source for this detailControls and installation checks before interpreting a code
Source for this detailFive verified PDF error codes
Source for this detailClear boundary between owner steps and repair
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
3.1 Cu. Ft. Stackable Front Load Washer MLH27N5AWWC
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.