MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MLTW39A1AWW
MLTW39A1AWW is a 3.9-cubic-foot top-load washer whose faults appear as four-light patterns rather than numeric codes.
Identify the compact agitator washer
MLTW39A1AWW is Midea's 3.9-cubic-foot top-load washer, built around a Power Boost agitator rather than an impeller-only tub. The manufacturer lists a 25.5-inch width, 28.3-inch depth and 42.1-inch height, so the machine may fit some narrower laundry spaces while still requiring room for the raised lid and hoses. Load Sensing weighs laundry to choose a fill level, and the product also offers a soft-close lid and a maximum spin speed of 700 rpm. Its display type is explicitly 'Indicator Lights'; there is no remaining-time display. That detail matters for diagnosis: the owner manual prints the exact model number on its cover, but the troubleshooting page depicts four lamp positions instead of an E-number on a screen. Treat the pattern as a visual status, not as a fabricated numeric fault code.
Prepare hoses, ventilation and level
An alcove or closet needs ventilation as well as enough space for this 25.5-inch body. The owner installation page requires two unobstructed openings with at least 72 square inches of combined area; its clearance drawing also distinguishes side, rear and top gaps. The hose instructions call for opening the water taps into a bucket for ten to fifteen seconds before connecting the lines to the washer, flushing out foreign material. Tighten the hose fittings as directed and check for leaks, since poor supply can produce a fault pattern later. Use a level on the cabinet reference edges rather than on the uneven lid surface. An unlevel washer can vibrate and affect spin. These installation checks are especially useful before interpreting a water or balance indication as a failed electronic sensor.
Use cycles and indicators correctly
The dial provides Normal, Bedding, Heavy Duty, Whites, Quick Wash, Delicates, Rinse & Spin and Tub Clean. Midea lists four wash-temperature choices and four water-level selections: Auto, Low, Medium and Deep Fill. Automatic load sensing is a convenience but does not remove the need to distribute clothes around the agitator. The manual's control illustration explains that cycle-status lamps show Fill, Wash, Rinse and Spin progress. Start/Pause can stop a cycle to add or remove items, although settings cannot be changed while paused; the rinse water remains cold even when a warmer wash temperature was selected. The liquid-softener compartment releases into the rinse when its option is selected. Do not mistake an ordinary flashing progress light for the fault pattern: the error page specifically says the Extra Rinse lamp flashes while the four process lights indicate the problem.
Check care and visible spin problems
Care and simple troubleshooting help interpret the signal. Run Tub Clean with no laundry inside; the care instructions warn that clothes in this cleaning cycle may be damaged. If the cabinet shakes or spin fails, first make sure the load is spread evenly and the washer stands on a stable level surface. The guide notes that a single robe or pair of jeans can leave the final spin unsatisfactory. The washer also will not spin with its lid open, and a kinked drain hose can prevent water leaving. If the cycle stops, check the lid and Start/Pause state before concluding that a control board is defective. These checks stay outside the electrical housing. For a pattern that remains after the applicable external checks, follow the service instruction attached to that row of the manual.
Read the four-light fault patterns
The rendered English table on PDF page 37 shows seven distinct left-to-right patterns. Empty circles mean off, double circles flash and filled circles stay on. OFF/OFF/OFF/FLASH is unusual: the same printed pattern covers both missing water supply and a malfunctioning water-level sensor. OFF/OFF/FLASH/OFF means no drain; OFF/OFF/FLASH/FLASH means the lid is open; OFF/FLASH/OFF/OFF means spin does not work. FLASH/ON/FLASH/ON means imbalance during spin, FLASH/OFF/FLASH/OFF means load sensing failed, and FLASH/FLASH/OFF/OFF means water-level sensing failed. The first pattern therefore cannot alone distinguish a closed tap from a sensor problem. The manual says the buzzer sounds for ten seconds, repeats every fifteen minutes and the washer powers off after 24 hours. Note all four positions before calling service; no numeral is displayed for these rows.
Verified model details
25.5-inch body with Power Boost agitator
Source for this detailEight dial-selected cycles and automatic fill sensing
Source for this detailSeven distinct four-LED patterns
Source for this detailFirst pattern can mean water supply or water-level sensor
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
Midea 3.9 cu. ft. Top Load Washer White
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.