MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MLTW45M1AWW
MLTW45M1AWW impeller washer: verified manufacturer manual, normal operation and safe interpretation of E1–CL display codes.
Confirm the impeller variant
MLTW45M1AWW is Midea's 4.5-cu-ft top-load washer with a Wave-Impeller. The same owner manual also covers MLTW44A1AWW, a 4.4-cu-ft agitator version, so the model suffix on the rating label matters. The exact product page describes the impeller pushing water upward and a glass window in a softly closing lid. It lists a digital display, lid lock, four selectable water levels and automatic or manual level control. The product dimensions are 27 inches wide, 28.1 deep and 42.1 high. Use these facts to identify the unit before applying a code table; they do not mean that every setting or part is shared with the agitator sibling.
Know the operating behavior
The exact product offers ten named cycles, including Quick Wash, Delicates, Rinse & Spin and Tub Clean. Water Plus lets you raise the level during a wash, while the operating instructions specify high-efficiency detergent to control suds. The display's remaining time is an estimate, and the manual says load size, incoming water temperature and pressure can change it. Sense, Soak, Wash, Rinse and Spin lights identify which stage is active. In an automatic cycle, the washer can move the clothes without water for roughly a minute to sense the load before filling. The troubleshooting chart also says its efficient low-water level is normal. Neither an early dry movement nor a changing time estimate alone establishes a fault.
Understand fill and drain faults
E1 has two documented triggers: slow filling at the selected water level and a water level that fails to change within ten minutes after fill. The manual gives 30, 45 and 60-minute limits for low, medium and high levels. Its installation section expects 14–116 psi water pressure. Before arranging service, check that both supply faucets are open, accessible hoses are not kinked, inlet screens are not clogged, and no visible connection leaks. E2 instead means the unit took over ten minutes to drain. Check the accessible drain hose for a kink and confirm its route matches the installation instructions. Do not confuse a naturally low water line with E1; use the displayed characters and the cycle stage.
Separate lid alarms from balance alarms
E3 means the lid is open. With Child Lock active, leaving it open for more than twenty seconds can sound an alarm, change the display to CL and drain the tub. The manual explains how to clear that alarm with Power and turn Child Lock off using Soil Level and Temp. E4 means the load became unbalanced more than three times during spin; redistribute the items rather than repeatedly starting the same uneven load. E5 points to an unlevel washer or failed impact switch. The installation chapter explains that poor leveling can cause vibration, excess noise and error codes. Check the level as directed; persistent E4 or E5 warrants Midea service.
Recognize service-level electronics faults
F2 denotes an EEPROM failure, F5 a load-sensing failure, F8 a water-level sensor failure, Fd a failed lid lock and C9 a failed control board. The manual sends these conditions to Midea's service center. Record the exact capitalization of Fd and the cycle behavior before calling; do not infer a failed component from an unrelated symptom. Never force the lid open or remove electronic covers as a response to a code. For routine care, the manual recommends drying the tub by leaving the lid open after use and running Tub Clean with an empty drum. These steps help maintenance but cannot repair a failed sensor or board.
Verified model details
Exact 4.5-cu-ft impeller variant, separate from agitator sibling
Source for this detailE1 has two documented fill-level triggers
Source for this detailE3 can progress to CL with Child Lock active
Source for this detailElectronic codes F2, F5, F8, Fd and C9 call for service
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
Midea 4.5 cu. ft. Top Load Washer with Wave-Impeller MLTW45M1AWW
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.