MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MPX1011CWRU
Midea MPX1011CWRU 10,000-BTU portable AC: visual EH60/EH61/EH0B codes and P1 drainage.
Identify the 450-square-foot smart portable model
MPX1011CWRU is Midea's 10,000-BTU DOE smart portable air conditioner for rooms up to 450 square feet. The exact US listing confirms cooling, dehumidifying and fan modes, no heat, dual filtration, a 24-hour timer and Sleep. It weighs 68.34 pounds and measures about 13.74 inches deep, 17.44 wide and 28.66 tall. The manufacturer links a two-model owner guide whose cover and wireless specification both print MPX1011CWRU. That matters because the companion MPX0812CWRU may have a different cooling capacity even though it shares the buttons and drainage instructions. Use the full SKU on the cabinet when comparing replacement hoses or describing a code. The room-size figure assumes an enclosed area; an open doorway into a larger space changes the load facing this portable unit.
Set up airflow before troubleshooting cooling
The installation section requires level ground, a grounded outlet, accessible water drain, at least twelve inches from a wall and roughly 19.7 inches clear of the outlet. Choose the correct slider pieces for a hung or sliding window and close their gaps with the included foam. The exhaust hose should reach the window without sharp bends or overextension and needs a free outlet beyond it. Cool is specified for ambient temperatures about 60–95 degrees Fahrenheit and Dry for 55–95. When the room remains warm, the troubleshooting chart starts with a clogged filter, a disconnected or blocked hose, open windows, an overly high target and too large a space. These conditions can defeat a 10,000-BTU unit without a sensor error. Only a technician should investigate refrigerant quantity; the R32 circuit is not an owner repair.
Distinguish three electronic faults from a full tray
The rendered control page shows EH60 for room-temperature sensing, EH61 for the evaporator-temperature sensor and EH0B for display-panel communication. The PDF's text extraction omits those graphical rows, so the row labels and meanings were transcribed from a hash-checked image of the actual page. EC52 and ELOC each say 'on some models' and have no exact-variant confirmation, so this guide does not claim them for MPX1011CWRU. P1 is different: it protects against a full bottom collection tray. The manual says P1 sounds eight beeps, stops cooling and dehumidification, but the fan can keep turning. Move the unit safely to a drain, empty it through the lower plug, refit that plug securely and restart. If P1 comes back after correct draining, contact service. Preserve exact capitalization when reporting EH0B.
Use cleaning and storage steps to prevent repeat symptoms
Midea recommends cleaning the air filter every two weeks and draining the tray immediately after P1. A pet household may need more frequent grille attention because hair blocks intake. When the appliance will be stored, empty the tray, run Fan for twelve hours in a warm room to dry internal moisture, clean and dry filters, then remove remote batteries. Continuous dehumidifying drainage uses an upper rear connection and a downward hose; it is not the same opening as the lower full-tray drain. A kink or a loose drain plug can create water problems without an electronic sensor code. The guide also warns to unplug before maintenance and to keep water out of electrical controls. If EH60, EH61 or EH0B persists after a simple restart, qualified service is appropriate rather than opening the refrigerant circuit.
Check remote sensing and app pairing separately
The product page advertises SmartHome, watch and voice control. Wireless setup is not an error: holding CONNECT for three seconds displays AP while a 2.4-GHz, IPv6-capable network and phone Bluetooth support Matter pairing. The manual's MyTemp option measures at the remote's location and sends a temperature reading every three minutes. A remote near sun or behind furniture can therefore make the perceived comfort different from the cabinet sensor without proving EH60. The panel's P1 requires water drainage, while AP only means enrollment and EH0B concerns panel communication. If the app disagrees with the appliance, test local Cool or Fan controls and note which display actually showed a code. Giving support the full SKU, room setup, drain condition and exact four-character label makes the report actionable.
Verified model details
Exact 10,000-BTU SKU on official cover
Source for this detail450-square-foot smart cool-only variant
Source for this detailEH60/EH61/EH0B read from rendered PDF p23
Source for this detailP1 full tray on PDF pp23–25
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
Midea 10,000 BTU DOE Smart Portable Air Conditioner MPX1011CWRU
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.