MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRF18B4AST
The exact MRF18B4AST owner PDF maps six flashing LED pairs to refrigerator, freezer and control faults.
Identify the stainless French-door unit
MRF18B4AST is the stainless, recessed-handle French-door refrigerator on Midea Canada's exact product page. The listed 18.4 cubic feet divides into 12.8 for fresh food and 5.6 for the freezer; its width is 29.5 inches. Two humidity-controlled crisper drawers, adjustable glass shelves and two freezer drawers explain the internal layout better than a generic cabinet diagram. The official owner PDF names both MRF18B4AST and white MRF18B4AWW on its first page. It therefore covers this SKU, but the manual warns that drawings and the actual control panel can differ by model. Compare the complete rating label and photographed panel before interpreting a signal. The product lists no water filter or dispenser and calls the compatible IM1900MD ice maker optional. An ice-maker installation section does not prove that an ice maker is fitted to this particular refrigerator.
Make the first temperature reading meaningful
The installation instructions call for more than 100 millimetres of clearance to adjacent walls. Level the cabinet so its front sits slightly higher than the rear; a door left ajar after a difficult close can imitate poor cooling. After connecting power, the manual says to wait two to three hours before adding food. Keep ventilation openings clear and leave the supplied drawers and shelves in their normal positions where possible. The control panel uses separate freezer and fridge buttons, and its startup display precedes normal operation by roughly three seconds. The shared manual prints refrigerator choices of 8, 4 and 2°C, and freezer choices of -16, -19 and -23°C. Midea's product specification instead gives ranges of 1–7°C and -22 to -14°C. Because these printed limits differ, use the actual panel and rating information rather than promising that every printed preset is available.
Read all six flashing LED pairs
Physical PDF page 12 identifies LED1/LED2 flashing as a refrigerator temperature sensor fault and LED1/LED5 as a freezer temperature sensor fault. LED1/LED3 concerns the freezing frost sensor. LED2/LED4 signals communication failure, a different category from a temperature probe. LED1/LED4 refers to the ambient temperature sensor; LED2/LED5 refers to the humidity sensor. The exact pair matters: LED1 appears in four separate rows and cannot diagnose anything alone. These are paired light positions on the described panel, not invented E-numbers. Photograph the whole panel while the lights flash and note whether the fresh-food or freezer compartment feels unusually warm. The manual cautions that cooling may continue with a fault visible, yet directs owners to a maintenance specialist. Do not use continued compressor operation as evidence that a persistent pair is harmless.
Separate alarm language from a sensor failure
This family manual describes a buzzer after either door remains open for 120 seconds and a short alarm-off press that silences a fault sound. The exact product listing does not clearly confirm a door-alarm feature, so test what the installed unit actually does rather than assuming its silence is another fault. A three-second hold on the same key enters standby and stops cooling; the manual says another long press restores normal control. Check that the panel is not in standby before treating a dark display as a power failure. The manual also says a fault code can replace the ordinary set-gear display. Record the visual pattern before silencing it or changing a setting. The owner-facing task is to describe a repeatable signal, not to open the control housing or replace a sensor from a chart.
Check the accessible causes and protect food
If there is no operation, the troubleshooting section starts with the plug, household supply and a tripped circuit. For a door that will not shut, look for food packages blocking it and check cabinet level; clean visible debris from the gasket. A warm room, repeated door openings and a large fresh load can lengthen compressor operation without matching any of the six LED faults. Keep warm food out until it has cooled, and do not place packages against the rear fresh-food wall where they may freeze. The manual recommends 4°C in the fridge and -19°C in the freezer for food storage under its stated ambient condition; verify actual temperatures when a warning appears. During a power interruption, reduce door openings and avoid adding new food. If a LED pair remains, protect perishables and tell qualified service the exact suffix, paired lights, temperatures and timing.
Verified model details
Exact 18.4-cu.-ft. Canadian French-door model
Source for this detailOptional ice maker versus installed equipment
Source for this detailSix verified LED-pair faults on PDF page 12
Source for this detailFood protection and qualified service
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
18.4 Cu. Ft. French Door Recessed Steel | Midea CA
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.