MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRF23I8AST
MRF23I8AST adds an AutoFill pitcher and ice maker to a counter-depth French-door refrigerator with twelve documented faults.
Identify the exact counter-depth layout
MRF23I8AST is Midea's stainless French-door Counter-Depth PLUS refrigerator with three doors and a lower freezer. The marketing name rounds capacity to 23 cubic feet; the detailed specification says 22.6 cubic feet, divided between 15.3 in the fresh-food area and 7.3 in the freezer. Its listed cabinet is 32.9 inches wide, 29.1 deep and 67.3 high. Measure the door swing as well: the owner dimensional drawing gives 56.10 inches of width with both doors open to 135 degrees. This model is freestanding even though its depth is designed to sit near surrounding counters. The exact product includes a full-width deli drawer, gallon door bins, crispers and SmartHome connectivity. The manufacturer-linked manual prints MRF23I8AST on its cover, so its controls and fault table can be tied to this SKU rather than a general refrigerator family.
Prepare the water and ice system
Water2Ways combines a 54-ounce AutoFill pitcher with a separate built-in dispenser, while the installed ice maker is marketed for up to 2.2 pounds of ice each day under appropriate conditions. The manual requires potable cold water and gives an inlet-pressure range of 276 to 689 kPa. Its water filter is inserted at the lower left of the refrigerating compartment and locked with a 90-degree clockwise turn. On first use, air and impurities must be flushed from the dispensing system; the guide specifies roughly 2.5 gallons in repeated thirty-second dispensing and sixty-second rest intervals, not one uninterrupted run. Check the water connection and leaks before judging a dry dispenser to be a failed electronic board. These steps belong to this plumbed model, whose pitcher and ice maker share the water-supply preparation.
Read normal display states before faults
At initial power-up, the owner guide sets the refrigerator to 4°C and freezer to minus 18°C. Ordinarily the display shows the refrigerator setting; a detected fault takes over the window in a cycling code display. The filter reminder is separate: it lights after 150 days and flashes after 180, then can be reset after replacement. Super Cool temporarily sets the fridge to 1°C for six hours, and Super Freeze sets the freezer to minus 22°C for forty hours before returning to the prior settings. Those temporary modes and filter icons should not be listed as failures. Another unusual display is `52` while adjusting the ice-maker inlet time; the manual says that represents the default 5.2 seconds, not an E fault. Record the exact characters and what task was under way before matching them to the code table.
Maintain AutoFill and the ice maker
The pitcher must sit squarely on its holder with the refrigerator door closed for AutoFill to work. The manual says that after power is restored, automatic filling can take about three minutes to become available. If filling stops, check the water pipes, remove and reseat the pitcher, and wipe moisture from its marked front area before trying again. The ice maker also has startup behavior: it begins only after the freezer reaches the required temperature, and its detection rod stops production when it reaches the ice in a full storage box. A slow first batch or a full bin is therefore not automatically an EP fault. Keeping the filter correctly seated and following the flushing routine matter for both features. These physical checks complement the appliance's electronic self-diagnostics without substituting for the displayed code.
Group the twelve actual fault codes
The rendered table on English PDF page 14 lists twelve specific faults. E1, E2 and E5 concern temperature sensing in the refrigerator, freezer and defrost system respectively; E7 is the ambient-temperature sensor, while EH is humidity sensing. E6 is communication between the display and main boards. EE concerns the ice maker's lower sensor and EP the ice maker itself. L3 and L4 distinguish a cooling-fan failure from abnormal cooling-fan speed; L5 and L6 make the same distinction for the condenser fan. The guide says cooling may continue despite one of these warnings but directs owners to a maintenance specialist to preserve normal operation. Do not infer a particular failed part from a filter icon, `52` setting or missing first ice batch. Read and report the actual code; the table gives fault descriptions, not a safe homeowner repair procedure.
Verified model details
22.6 actual cubic feet in a 32.9-inch body
Source for this detailWater2Ways pitcher, dispenser and ice maker
Source for this detailFilter reminders and temporary cooling modes
Source for this detailTwelve specific E, EH, EE, EP and L faults
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
Midea 23 cu. ft. Counter-Depth PLUS™ French Door Refrigerator + Water2Ways™ AutoFill Pitcher + Ice Maker MRF23I8AST
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.