MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRT14D2BST
MRT14D2BST is Midea Canada's 14.2-cu-ft stainless top-freezer refrigerator with reversible doors and three verified two-LED fault patterns.
Identify the 28-inch stainless model
MRT14D2BST is Midea Canada's stainless-steel top-freezer refrigerator in the 14.2-cubic-foot family. Its exact listing divides that capacity into 10.53 cubic feet of fresh-food space and 3.67 frozen, inside a 27.6-inch-wide, 28.8-inch-deep and 60.6-inch-high cabinet. The stated weight is 144.4 pounds and the sound figure is 42 dB. The owner PDF cover explicitly includes MRT14D2BST alongside D2 and D3 colour variants; its family specification confirms the 14.2-cubic-foot volume and 115-volt, 60-hertz supply. Midea advertises multi-airflow, electronic control and an LED interior light. The product is ice-maker ready: that means provision for an optional maker, not evidence that one is already installed. This distinction matters when comparing accessory advice or a code list from a refrigerator with built-in ice equipment.
Install it for the room and door swing
Midea markets the model for unheated areas within a stated 3°C to 43°C ambient range, but the owner guide still requires a flat, sturdy, ventilated indoor location. It says the appliance must stand freely, with more than 100 mm between adjacent walls, and cannot be recessed into cabinetry. The reversible doors let an installer adapt the swing; the manual shows a detailed upper, middle and lower hinge procedure with left-side components. Plan the hinge direction and the clearance before moving the cabinet into place. After initial placement, the guide says to leave it two hours before connecting power and allow another two to three hours of running before loading food. Level the feet so the front is slightly higher than the rear, helping the doors close. Neither a reversible door nor a garage-ready claim removes the need for airflow around the condenser.
Understand the four-light control
The control panel uses four labelled LEDs and one temperature-setting button, not a numeric display. Each press advances one setting and the refrigerator applies the selected level after about fifteen seconds. Super Cool temporarily runs at its coldest setting and ends automatically after six hours. A long three-second press on the setting key unlocks the panel; with no further input it relocks after fifteen seconds. In normal operation, the lit LEDs describe the selected cooling level. Watch whether a lamp is steady or flashing before treating the panel as a diagnostic signal. The actual product also has adjustable glass shelving and a fruit-and-vegetable box. Food placed against the rear wall or warm food put straight into the compartment can disturb storage performance. Set the strength for the load and ambient conditions rather than assuming the coldest position is always better for produce.
Handle everyday care before diagnosing
Routine care and a fault pattern call for different actions. The guide describes automatic defrosting, while its troubleshooting table first asks about the plug, partial circuit trips, packages preventing a door from closing and whether the floor is level. These checks can explain warmth, noise or poor door closure without a sensor failure. If electricity is interrupted, open the doors as little as possible and avoid adding fresh food during the outage. For cleaning, remove shelves and the crisper carefully and use the nonabrasive approach in the guide. LED lamp replacement is reserved for the manufacturer, service agent or a similarly qualified person. A sound from the compressor or a brief change as the thermostat settles is not equivalent to the particular two-lamp patterns on page 16. Record how the LEDs behave before arranging service.
Match the three fault pairs
The rendered owner's table on PDF page 16 contains three fault patterns. LED1 and LED2 flashing together mean a refrigerator temperature-sensor fault. LED1 with LED3 flashing indicates a freezer frost-sensor fault. LED1 with LED4 flashing indicates failure of the ambient-temperature sensor. The fourth LED is part of the normal control display, but the table names no LED1-plus-LED4-plus-other combination as an additional fault. These are descriptions of simultaneous blinking positions, not codes shown as letters or numbers. Because LED1 appears in all three, identify the second flashing lamp before describing the problem. A normal fifteen-second lock or a changed temperature setting does not identify any sensor. Tell service MRT14D2BST and the exact pair seen; avoid opening internal sensor wiring on the strength of a light pattern alone.
Verified model details
14.2-cu-ft narrow top-freezer cabinet
Source for this detailIce-maker ready, with no installed maker promised
Source for this detailElectronic temperature gear and six-hour Super Cool
Source for this detailThree precise flashing LED pairs on PDF page 16
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
14.2 Cu. Ft. 28" Top Mount Freezer Refrigerator MRT14D2BST
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.