MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRT14D2BWW
The white MRT14D2BWW has a separate top freezer and three documented flashing LED pairs, with normal settings on the same panel.
Match the white two-door cabinet
Midea Canada's MRT14D2BWW listing describes a white 14.2-cubic-foot refrigerator with a freezer above the fresh-food compartment. The split is 3.67 cubic feet frozen and 10.53 cubic feet fresh, in a body 27.6 inches wide, 28.8 deep and 60.6 high. This is not the convertible single-chamber MRU line: an upper freezer and lower refrigerator work at the same time. The exact white page's embedded Documentation API links a PDF whose cover explicitly includes MRT14D2BWW among six D2/D3 finish variants. Compare the complete label before using that family manual. The product advertises multi-airflow cooling, electronic control, LED lighting and an ice-maker-ready connection; ready is not proof an accessory is fitted. Although another specification field mentions a steel door finish, the exact colour field says White, so this article makes no claim about door material.
Load the two sections with their different jobs
The manual's overview identifies a glass shelf in the top freezer and separate refrigerator glass shelves plus a fruit-and-vegetable box below. Frozen packages should go back upstairs quickly after shopping, with new unfrozen food kept apart from items already frozen. In the fresh compartment, cool warm dishes first and avoid uncovered liquids or containers touching the back wall. Do not overfill either space, because cold air must move around the stored items; Midea's multi-airflow claim does not cancel that basic need. The white product is listed as ice-maker ready, yet the manual illustration may show an optional tray rather than equipment actually supplied. Use the real shelves and label to identify what is present. A warm lower section with a normal upper freezer calls for checking door sealing and loading before attributing both to the same sensor.
Prepare the location and reversible doors
The product gives a tested ambient range of 3 to 43 degrees Celsius for its garage-ready claim; the owner guide still asks for a firm, ventilated indoor, freestanding position. Avoid blocking the spaces around the cabinet and use a grounded 115-volt, 60-hertz supply appropriate to the rating plate. Its instructions explain reversing the upper and lower door swing with separate hinge parts, so a loose seal after a reversal deserves attention. Level the cabinet with its front slightly higher than its rear to help both doors close. Before connection after placement, the manual prescribes a two-hour wait; after switching on, allow another two to three hours of cooling before loading food. A crowded or tilted refrigerator can appear to cool poorly without showing the paired LED faults. Move contents and secure shelves before transport, and keep the cabinet upright.
Tell a setting from a warning
There are four numbered lamps and one Setting button. Each short press changes the chosen level, which takes effect after roughly 15 seconds. Super Cool runs the fresh-food side at maximum capacity for up to six hours, so a temporary strong cooling phase is expected when that mode is chosen. The panel locks again after 15 seconds without input; a three-second Setting hold unlocks it and makes all LEDs blink for two seconds. Those brief unlock flashes are an interface acknowledgement, not a persistent sensor code. On first power the display shines fully for three seconds. When healthy it shows the temperature setting; in a failure the relevant LED pair flashes. Watch an entire cycle, record whether the control was being unlocked or Super Cool was selected, and then compare the two flashing numbers to the manual table.
Use the three fault rows and safe checks
On physical PDF page 16, LED1 together with LED2 flashing identifies a refrigerator temperature-sensor fault. LED1 plus LED3 flashing is labelled freezing frost sensor fault; LED1 plus LED4 flashing is ambient temperature-sensor failure. LED1 alone cannot distinguish the rows, and the printed names are paired lights rather than E-number codes. Photograph the white unit's whole panel before resetting or unplugging it. If cooling seems weak, first check power, a tripped household circuit, food packages blocking either door and cabinet level, as the troubleshooting page directs. During an outage, keep doors closed and avoid adding food. If the same pair returns after these external checks, protect perishables and tell qualified service the full MRT14D2BWW model, pair, compartment temperature and recent Super Cool state. Internal LED-lamp and sensor work belongs to trained personnel.
Verified model details
Exact 14.2-cu.-ft. white model
Source for this detailTop and lower compartments have separate storage needs
Source for this detailThree pairs verified on PDF page 16
Source for this detailCheck closure and power before service
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
14.2 Cu. Ft. 28" Top Mount Freezer Refrigerator MRT14D2BWW
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.