Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRU21F6AWW
The white MRU21F6AWW changes a single 21-cu.-ft. chamber between fridge and freezer use; three LED pairs flag sensor faults.
Identify the white full-height unit
MRU21F6AWW is Midea Canada's white 21-cubic-foot upright freezer that converts to refrigerator use. The product describes a flat door, recessed handle, LED interior lighting and controls placed within 46 inches for access. Its 29.72-by-32.68-by-66.61-inch body and four door shelves help distinguish it from a compact freezer. The exact white page embeds a Documentation API linking the owner PDF, whose cover names MRU21F6AWW beside stainless MRU21B6ASL. That shared cover establishes family scope; compare the rating plate because another tall Midea cabinet could look similar. This model changes the role of one chamber, so moving from frozen-food storage to beverages means changing its entire thermal state. The garage-ready claim states different ambient test ranges for fridge and freezer modes, which is useful when choosing a location but does not turn the appliance into outdoor equipment.
Set the intended temperature before loading
After connection, the panel briefly illuminates in full for three seconds and starts with COLDER / FRZ. Cold, Colder and Coldest are selectable levels; a new setting is adopted after approximately 15 seconds, while the food and cabinet need longer to equilibrate. With the controller unlocked, holding Setting three seconds extinguishes the freezer icon and turns the chamber into a refrigerator. Repeating the hold illuminates it again and returns freezer operation. A lit icon that simply indicates FRZ or a chosen coldness level is not a fault. The manual says that during failure the corresponding LEDs blink, whereas normal operation displays the setting. Write down the selected mode before moving food, and verify a safe temperature with an independent thermometer once the chamber has stabilized. The printed control image may not exactly match every covered unit.
Give the white cabinet room to work
Install it on a firm, well-ventilated indoor floor as a freestanding appliance. The manual requires an individual grounded 115-volt, 60-hertz receptacle that agrees with the rating label. Set the adjustable feet so the front stands slightly above the back and the tall door shuts reliably. Although the door is reversible, Midea directs owners to its after-sales team for the hinge reversal, which includes wiring at the top. On initial startup, let the compartment run two to three hours before putting in food; in a hot summer, the guide asks for more than four hours. Keep warm dishes out until cooled and do not obstruct interior airflow with crowded shelves. When moving, empty and secure loose shelves, maintain the upright position and avoid tilting over 45 degrees. These physical conditions can affect cooling without producing one of the three electronic patterns.
Read the three paired flashes exactly
Rendered manual page 13 prints LED3/LED4 flashing for a refrigerator temperature sensor fault. LED2/LED4 flashing is described as “Freezing frost sensor faults,” an awkward manufacturer phrase that should be reported as printed. LED1/LED4 flashing refers to an ambient temperature sensor fault. The shared LED4 position appears in every row, so it cannot diagnose anything alone. A steady light used for the Cold scale also does not satisfy the table: observe whether both members of a pair blink. Photograph the whole display and record the white model's current fridge or freezer mode, since a conversion may have occurred before the fault. No alphanumeric E code appears in this table. Its descriptions are service clues rather than proof that a sensor should be replaced or that stored food remains at a safe temperature.
Protect the contents and describe the symptoms
If operation stops, check the plug, household circuit and local power before assuming a controller defect. Remove packages that prevent the flat door from sealing and confirm the cabinet is level. Compressor cycles can lengthen when the room is hot, after a large load or with repeated door openings. In refrigerator mode, keep liquids covered and containers away from the rear wall; the manual describes automatic defrost but still calls for mild noncorrosive cleaning. During an outage, keep the door closed as much as possible and do not add fresh food. A warm outer wall may be normal condenser heat, and humidity can cause exterior moisture. If the same paired blink persists, transfer vulnerable food and tell qualified service MRU21F6AWW, both LED numbers, chosen mode, measured temperature and recent loading. Leave internal lamp and sensor work to trained people.
Verified model details
Exact white Canadian cabinet and PDF
Source for this detailChoose mode before filling the single chamber
Source for this detailLED3/4, LED2/4 and LED1/4 on page 13
Source for this detailDoor, power and food checks
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
21 Cu. Ft. Convertible Upright Freezer White | Midea CA
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.