MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Midea MRW34B4ABB
The MRW34B4ABB wine cabinet has two actual display faults, E1 and E6, distinct from its FC rapid-cool mode.
Match the wine cabinet, not a generic refrigerator
Midea Canada's MRW34B4ABB listing describes a black, 3.3-cubic-foot glass-door wine cooler advertised for 34 bottles. It is 18.5 inches wide according to the product specification, with recessed handle, electronic control and interior LED lighting. The manufacturer's owner PDF is named by the exact product's embedded Documentation API. Its rendered first page visibly says MRW34B4ABB even though the PDF's embedded font garbles that SKU in extracted text; the specification page prints the model normally. Check the complete label before treating any display symbol as applicable. The manual uses the broader term “beverage cooler,” but its bottle-loading section and separate product description establish this wine-cabinet use. Bottle count is based on a particular illustrated size; larger shapes reduce real capacity. Do not push bottles against the rear wall, since that blocks circulation.
Place and start the compact cabinet
The owner manual asks for more than 100 millimetres between the cabinet and adjacent walls. After transportation, let it stand for more than two hours before energizing it. The product advertises adjustable levelling legs and low-emissivity, tempered anti-UV glass; use a stable floor and keep the glass clear of hard objects. The manual warns that some frost or water droplets on the rear interior can form during compressor operation and later run to the evaporation tray. A moist rear wall alone is therefore not E1. It also warns against restarting within five minutes of a disconnection. If cooling seems delayed after a move, check the placement, time since connection, bottle load and door seal before touching the electronics. The exact PDF specification gives 115 V, 60 Hz and 1 A; compare the unit's own rating plate for the installation.
Distinguish FC and ordinary temperature display
The glass door carries touch controls. At power-up the display briefly lights fully and sounds a start tone, then normally shows the set temperature. A long three-second press of Standby darkens the display, while another long press exits standby. The lighting key controls the interior lamp separately. To enter Super Cool, hold Standby and Lighting together for three seconds; FC then appears and the mode ends automatically within 24 hours. FC is a deliberate operating mode, not a fault code. Holding the temperature-up and temperature-down keys together switches between Celsius and Fahrenheit. Each short temperature-key press moves the setting by one degree. The printed range is 1 to 10°C or 34 to 50°F. Power-off memory restores the previous setting. Record the displayed letters and recent button presses before deciding the cabinet is broken.
Interpret the two real fault messages
The verified table on physical PDF page 9 gives E1 as temperature sensor fault and E6 as communication fault. These labels concern different parts of the control system; neither tells an owner to buy a particular sensor or board. The text directs the user to contact a specialist for maintenance when a fault code is shown. E1 is not the same as an unexpectedly warm cabinet after adding too many bottles: that load can temporarily increase temperature without a printed code. E6 does not refer to switching Celsius and Fahrenheit, which is a manual setting operation. Photograph the exact letters and the current cabinet temperature, and note whether FC had been selected. A blank screen calls first for a standby and power check. Do not remove the glass-door control panel or probe wiring on the basis of a two-character display alone.
Keep bottles and glass safe while investigating
For a cooler that will not run, the troubleshooting table starts with plug contact, low supply voltage and a tripped circuit. Longer compressor operation in summer, frequent glass-door opening or a large new beverage load can be ordinary. Wipe external condensation when ambient humidity is high and check that the door gasket is free of debris. For cleaning, unplug, remove bottles and shelves, and use soft materials; do not soak the door controls or lighting. The manual specifically says wooden wine racks should not be immersed, because moisture can cause cracking or mold. It also warns against abrasive pads and scraping the glass. If an E1 or E6 returns after accessible checks, protect temperature-sensitive bottles and give service the exact MRW34B4ABB suffix, code, setting, room conditions and a photograph. This preserves useful evidence without risking the sealed cooling circuit.
Verified model details
Exact 34-bottle, 3.3-cu.-ft. black cabinet
Source for this detailGlass-door controls and FC mode
Source for this detailE1/E6 verified on owner PDF page 9
Source for this detailBottle layout, cleaning and service
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
3.3 Cu. Ft. Bottle Wine Cooler Glass Door | Midea CA
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.