MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Samsung WF45T6000AV/A5
WF45T6000AV/A5 is the black front-load washer on Samsung Canada's exact product page.
Match the black AV model to its actual equipment
WF45T6000AV/A5 is the black front-load washer on Samsung Canada's exact product page. That page expresses one drum as 5.2 cu ft by IEC and 4.5 cu ft by DOE measurement; the linked WF45T6000A* owner sheet uses 4.5 cu ft. The different figures describe measurement methods rather than two selectable tub sizes. The product specifies an LED display, 1,200 rpm spin, VRT+ vibration reduction and ten cycles. Just as useful for troubleshooting are its explicit absences: no internal heater, no steam, no Super Speed and no Smart Control. The family booklet prints an HC heater row, but that row does not establish a heater in this SKU. Similarly, Smart Care is a local phone-based reading aid and should not be mistaken for remote cycle control. Keep the exact AV/A5 suffix when comparing a feature list, because the manual cover describes a family rather than every finish and market configuration.
Check the installation before interpreting vibration or leaks
Physical page 21 of the owner tells the installer to remove the transit bolts before the first cycle and place the machine on a solid, level floor. Page 22 explains how the leveling feet and locking nuts are adjusted; it also calls for new inlet hoses with rubber gaskets and five inches behind the washer to avoid kinking them. After connecting the hoses, page 23 says to briefly flush the lines into a bucket before attaching them to the appliance. The drain pipe or laundry tub has a height window from 18 to 96 inches on page 24. A drain hose pushed too far into a standpipe or installed below the minimum may behave differently from a blocked pump. These installation details give UB, LC, 4C and 5C useful context. For a newly installed machine that shakes, first confirm the transport bolts are gone, feet are locked and the load is spread out. For water at the back, inspect couplings and gaskets rather than assuming the drum seal has failed.
Understand what each panel control can and cannot do
The cycle dial and separate Temp., Rinse, Spin and Soil buttons are described on pages 32 and 33. The display may show an information code in place of its usual time. Spin Only is selected by holding Spin for three seconds; Rinse Hold deliberately leaves clothing in the final rinse water until a drain or spin is chosen. Neither state by itself proves a drain fault. Delay End asks when the wash should finish, up to 24 hours later, rather than promising that it will start after the number displayed. Child Lock is toggled with Temp. and Rinse held for three seconds and disables the panel while locking the door. An unresponsive key or closed door should be checked against that setting before replacing electronics. Samsung lists Smart Care, which reads the display through a phone camera or accepts a manually entered code. It expressly lists Smart Control as absent, so there is no supported app command to start a cycle remotely on this exact AV machine.
Read the supported codes through their physical systems
On physical page 55, 1C means the water-level sensor needs checking, DC shows an open door, DC1 points to the door switch and LC calls for a leak check. The same page uses 4C for supply, 4C2 for water entering too hot and 5C for drainage. Page 56 adds UB for spin balance; 8C, 8C1 and 8C2 for the MEMS sensor; OC for possible overflow; 3C for motor operation; AC6 for control communication; 9C1 and 9C2 for electronic control; and SF for system failure. Those seventeen strings are distinct, including each numbered sensor variant. HC appears in the shared PDF, yet the exact product page says Internal Heater: No, so this catalog excludes HC from the applicable AV code list. If OC appears, the manual asks for the water valve to be shut and service called. SF likewise directs the user to power off and contact service. Several other codes allow one power-off, two-to-three-minute wait and retry, followed by service when the message returns.
Use routine care to avoid confusing reminders with faults
The product's Self Clean+ cycle is a maintenance function, and the manual's reminder appears after forty cycles. Run it with an empty drum instead of treating its icon as a new error. The owner asks for low-suds HE detergent and keeps liquid detergent in its insert; remove that insert before using powder. A blocked inlet mesh can produce 4C, whereas a blocked drain or pump filter can produce 5C, so the filters are not interchangeable checks. Page 52 says water remaining in the drum prevents the door from opening; after a paused fill or subsequent drain, the lock can take time to release. If a load ends wet, first check for a kinked drain hose, a very small unbalanced load or a low spin setting. Record the exact code and the check you performed. That is more informative for Samsung service than a general complaint that the washer stopped.
Verified model details
Match the black AV model to its actual equipment
Source for this detailCheck the installation before interpreting vibration or leaks
Source for this detailUnderstand what each panel control can and cannot do
Source for this detailRead the supported codes through their physical systems
Source for this detailUse routine care to avoid confusing reminders with faults
Source for this detail
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
5.2 cu. ft. Front Load Washing Machine with Self Clean+ Black | Samsung Canada
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.